Can’t see what you need? Some parts may not be listed, drop us an email info@hyperformance.nz
It takes a lot of time and effort, but the bearings on the Upper Link can wear out. This is a replacement upper link for the HD6
Details:
Forged Aluminum 6061-T6
CNC machined
Anodized finish
Includes bearings
Bolt kit sold separately
NZ delivery only.
Replacement bearings for the upper swingarm pivot point of the HD6.
Details:
Two custom spec bearings specifically made for use as pivot bearings
Extra tight seal rings to hold in a 100% fill of waterproof grease
This is the kit to replace your entire lower link assembly on the Ripmo V3, Ripley V5, and HD6.
All the hardware and replacement bushings / o-rings are included.
This link is wider than previous bushing models, the 71mm etching notes that it is the wider link kit for the Ripmo V3/Ripley V5/HD6 only.
Replacement axle for models with the UDH.
Length 174mm
Thread Pitch 12x1.0
Torque to 10nm
43 grams
Replacement hanger for UDH models.
Includes fixing bolt and washer.
26 grams
Note: the washer is required to install on to the frame. Damage will occur if a hanger is mounted without the washer under the main fixing bolt.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Finally putting the Ride More Work Less logo to good use, this handy flask will safely house the fine contents of any tasty beverage. Made of 18/8 grade stainless and holds 4oz of goodness. UV cured printed logo.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
Compatible With
Mojo HD3
Mojo HD4
Mojo HD5
After an extended period of use, you might want to check these bushings for wear.
2x Igus Bushings
4x Reducer hardware (2x outer; 2x inner)
4x O-rings 18x1
2x Ti clevis to swingarm bolts
NZ delivery only.
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
4 mounting bolt kit for upper links.
Compatible With
Ripmo AF
Ripmo 1 - 2
Ripmo V2S
HD5
HD4
HD3
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
Compatible With
Mojo HD5
Mojo 4
Downtube Rock guard
Polycarbonate
Protects downtube from rock strikes
Includes stainless steel M4x10 mounting bolts
Available in 2 sizes per your specific frame size
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Replacement eyelet hardware from Fox.
This kit will allow you to refresh an existing shock or an aftermarket shock that doesn't come with the correct hardware to match the specs of our current models.
Fox part numbers for reference: Front 21.8mm wide: 803-03-165
Fits following models:
Mojo 3
HD4
HD5
Ripley 1 & 2
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
Finally putting the Ride More Work Less logo to good use, this handy flask will safely house the fine contents of any tasty beverage. Made of 18/8 grade stainless and holds 4oz of goodness. UV cured printed logo.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
HD3 Lower Link Assembly
Options for Non-Boost or Boost swingarms
Forged Aluminum
CNC machined
Anodized
Includes bearings
Super easy to replace
No special tools needed
NZ delivery only.
Ibis Mojo HD3 Upper Link Assembly
Forged Aluminum
CNC machined
Anodized
Includes bearings
Super easy to replace
No special tools needed
NZ delivery only.
4 mounting bolt kit for upper links.
Compatible With
Ripmo AF
Ripmo 1 - 2
Ripmo V2S
HD5
HD4
HD3
This is the set to install a lower link to a Mojo 3 or HD3 with boost 148 swingarm.
2 link shafts and 2 fixing bolts.
Torque to 24nm, Loctite 243 recommended.
NZ delivery only.
This is the set to install a lower link to a Mojo HD3 with original 142mm spacing swingarm.
2 link shafts and 2 fixing bolts.
Torque to 24nm, Loctite 243 is recommended.
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Replacement eyelet hardware from Fox.
This kit will allow you to refresh an existing shock or an aftermarket shock that doesn't come with the correct hardware to match the specs of our current models.
Fox part numbers for reference: Front 21.8mm wide: 803-03-165
Fits following models:
Mojo 3
HD4
HD5
Ripley 1 & 2
NZ delivery only.
Compatible With
Mojo 3
Mojo HD3
Mojo HD4
Polycarbonate
Protects Cables and Downtube from Rock Strikes
Lightweight
Mounts via 2 Under Downtube Bolts on Mojo HD3 or Mojo3 SM/MD frame, 4 bolts on LG/XL size frame. Bolts do not come with guard as they should be affixed to your bike frame.
Available in 2 sizes
NZ delivery only.
Compatible With
Mojo HD3
Mojo HD4
Mojo HD5
After an extended period of use, you might want to check these bushings for wear.
2x Igus Bushings
4x Reducer hardware (2x outer; 2x inner)
4x O-rings 18x1
2x Ti clevis to swingarm bolts
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
Lower link kit for Exie.
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
Replacement upper link for Ibis Exie
Forged Aluminum link
CNC machined
Bearings preinstalled
Anodized black finish
Includes 4 mounting bolts
NZ delivery only.
C29S Swingarm Service Kit
This is the swingarm bushing service kit for Exie, Ripmo V2S, and Ripley V4S.
It is not compatible with V1 or V2 Ripmo, the Ripley V4, or AF bikes.
4x 11.5mm O-rings
4x reducers
4x bushings
2x bolts and tear drop nuts
NZ delivery only.
Replacement axle for models with the UDH.
Length 174mm
Thread Pitch 12x1.0
Torque to 10nm
43 grams
Replacement hanger for UDH models.
Includes fixing bolt and washer.
26 grams
Note: the washer is required to install on to the frame. Damage will occur if a hanger is mounted without the washer under the main fixing bolt.
Ibis Logo T-Shirt
Size: XL
Colour: Orange with Black Ibis logo
Cotton Polyester
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Flip chips can be easily misplaced. That's where this kit comes to the rescue.
The Ripmo V3 and Ripley V5 utilize a set of flip chips in the swingarm to adjust for rear wheel size. The flip chip position is clearly marked on the swingarm and should always match the rear wheel size installed. A mismatch between the flip chip position and rear wheel size will negatively impact the bike's geometry.
The flip chip bolt has a 15nm torque spec. Ensure the bolt threads are treated with Loctite 243 or that a green thread patch is present.
NZ Delivery Only
Replacement axle for models with the UDH.
Length 174mm
Thread Pitch 12x1.0
Torque to 10nm
43 grams
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
Replacement hanger for UDH models.
Includes fixing bolt and washer.
26 grams
Note: the washer is required to install on to the frame. Damage will occur if a hanger is mounted without the washer under the main fixing bolt.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Ibis Logo T-Shirt
Size: XL
Colour: Orange with Black Ibis logo
Cotton Polyester
NZ delivery only.
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
Compatible With
Ripley AF
Ripley 4
Ripley V4S
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts.
If you simply need upper link bolts, you can purchase them from the dropdown menu..
NZ delivery only.
Replacement axle for models with the UDH.
Length 174mm
Thread Pitch 12x1.0
Torque to 10nm
43 grams
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
C29S Swingarm Service Kit
This is the swingarm bushing service kit for Exie, Ripmo V2S, and Ripley V4S.
It is not compatible with V1 or V2 Ripmo, the Ripley V4, or AF bikes.
4x 11.5mm O-rings
4x reducers
4x bushings
2x bolts and tear drop nuts
NZ delivery only.
Seattube rubber protector (50A durometer - soft and supple like your Minions.. ) to stick onto the swing arm of your Carbon Ripmo or Ripley V4 frame to guard against rock deflection onto the lower link.
Use this link for the instruction manual for installation
Fitment is for carbon Ripmo and Ripley V4 frames only. DOES NOT fit any of the Mojo HD's or Mojo 3, earlier Ripleys or the Ripmo/Ripley AF.
This is the protection piece for carbon frames that have the upper link attachment point behind the seat tube. If you need to replace it or add one, it's as easy as peeling off the backing, cleaning the area on your frame, and applying it to the best fit you can. It may be easier to remove the upper link to allow for more working room.
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
Compatible With
Ripley AF
Ripley 4
Ripley V4S
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts.
If you simply need upper link bolts, you can purchase them from the dropdown menu..
NZ delivery only.
This is the Ripley V4 swingarm bushing service kit
4x 1x14 O-rings
4x reducers
2x bushings
2x bolts and nuts for the clevis to swingarm
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
Compatible With
Ripmo V1
Ripmo V2
Ripley V4
Polycarbonate
Protects Downtube from Rock Strikes
Lightweight
Mounts via 2 Under Downtube Bolts on the carbon Ripmo and Ripley V4 frames. Bolts do not come with guard as they should be affixed to your bike frame. If you need a spare bolt let us know.
NOTE: This does NOT work on the Ripmo AF.
Available in black and, well, black
NZ delivery only.
Seattube rubber protector (50A durometer - soft and supple like your Minions.. ) to stick onto the swing arm of your Carbon Ripmo or Ripley V4 frame to guard against rock deflection onto the lower link.
Use this link for the instruction manual for installation
Fitment is for carbon Ripmo and Ripley V4 frames only. DOES NOT fit any of the Mojo HD's or Mojo 3, earlier Ripleys or the Ripmo/Ripley AF.
This is the protection piece for carbon frames that have the upper link attachment point behind the seat tube. If you need to replace it or add one, it's as easy as peeling off the backing, cleaning the area on your frame, and applying it to the best fit you can. It may be easier to remove the upper link to allow for more working room.
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
Compatible With
Ripley AF
Ripley 4
Ripley V4S
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts.
If you simply need upper link bolts, you can purchase them from the dropdown menu..
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
This is the service kit needed when performing maintenance of the swingarm bushings on an Ibis aluminum frame. After an extended period of use, you might want to check these bushings for wear.
2x Igus Bushings
4x Reducer hardware (2x outer; 2x inner)
4x O-rings: 2 each of 1mm x 16mm & 1mm x 21 mm
2x Clevis to swingarm bolts
*Please note this kit is not compatible with the RipMo carbon frames*
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
Ripley Rockguard
Polycarbonate
Protects Downtube from Rock Strikes
Lightweight
Mounts via 2 Under Downtube Bolts on Ripley 1, 2 LS & 3
Available in black and, well, black
NZ delivery only.
Compatible With
Ripley 1
Ripley 2
Ripley 3
Includes Enduro "MAX" black oxide bearings.
2 - 608 (swingarm, lower)
2 - 698 (swingarm, upper)
4 - 6806 (front triangle eccentrics)
The Ripley uses only 8 total bearings per frame. What Does 'MAX" Mean? Read about Enduro bearings here: http://www.enduroforkseals.com/id172.html
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
Compatible With
Ripley 1
Ripley 2
Ripley 3
Includes Enduro "MAX" black oxide bearings.
2 - 608 (swingarm, lower)
2 - 698 (swingarm, upper)
4 - 6806 (front triangle eccentrics)
The Ripley uses only 8 total bearings per frame. What Does 'MAX" Mean? Read about Enduro bearings here: http://www.enduroforkseals.com/id172.html
NZ delivery only.
This GnarCore eccentric pack is the replacement for the lower/upper eccentric cores on the Ibis Ripley V1 or V2 LS.
All hardware is included to refresh both the top and bottom cores (2 eccentric links in pack). We recommend new bearings when performing maintenance on these.
NZ delivery only.
Mojo 3/ Ripley V2 Clevis Bushing Service Kit
Parts kit for Ripley & Mojo3 Clevis to Swing Arm w/ bolts
NZ delivery only.
This is the bushing kit for the clevis to swingarm bushings on the Ripley V1. After an extended period of use, you might want to check these bushings for wear.
2x Igus Bushings
4x Reducer hardware
4x O-rings 14x1
2x M6x180 bolts
Ripley Rockguard
Polycarbonate
Protects Downtube from Rock Strikes
Lightweight
Mounts via 2 Under Downtube Bolts on Ripley 1, 2 LS & 3
Available in black and, well, black
NZ delivery only.
Replacement eyelet hardware from Fox.
This kit will allow you to refresh an existing shock or an aftermarket shock that doesn't come with the correct hardware to match the specs of our current models.
Fox part numbers for reference: Front 21.8mm wide: 803-03-165
Fits following models:
Mojo 3
HD4
HD5
Ripley 1 & 2
NZ delivery only.
This is the kit to replace the forward and rear shock mounting bolts.
1 x Forward ti pin with stainless steel bolts
1 x Rear Clevis to Shock bolt / nut
NZ delivery only.
Compatible with
Ripley 1 & 2 LS
Replacement axle for models with the UDH.
Length 174mm
Thread Pitch 12x1.0
Torque to 10nm
43 grams
Replacement hanger for UDH models.
Includes fixing bolt and washer.
26 grams
Note: the washer is required to install on to the frame. Damage will occur if a hanger is mounted without the washer under the main fixing bolt.
Flip chips can be easily misplaced. That's where this kit comes to the rescue.
The Ripmo V3 and Ripley V5 utilize a set of flip chips in the swingarm to adjust for rear wheel size. The flip chip position is clearly marked on the swingarm and should always match the rear wheel size installed. A mismatch between the flip chip position and rear wheel size will negatively impact the bike's geometry.
The flip chip bolt has a 15nm torque spec. Ensure the bolt threads are treated with Loctite 243 or that a green thread patch is present.
NZ Delivery Only
This is the kit to replace your entire lower link assembly on the Ripmo V3, Ripley V5, and HD6.
All the hardware and replacement bushings / o-rings are included.
This link is wider than previous bushing models, the 71mm etching notes that it is the wider link kit for the Ripmo V3/Ripley V5/HD6 only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Ibis Logo T-Shirt
Size: XL
Colour: Orange with Black Ibis logo
Cotton Polyester
NZ delivery only.
COMPATIBLE WITH
Ripmo AF
Ripmo 1 - 2
Ripmo V2 S
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts.
NZ delivery only.
4 mounting bolt kit for upper links.
Compatible With
Ripmo AF
Ripmo 1 - 2
Ripmo V2S
HD5
HD4
HD3
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
C29S Swingarm Service Kit
This is the swingarm bushing service kit for Exie, Ripmo V2S, and Ripley V4S.
It is not compatible with V1 or V2 Ripmo, the Ripley V4, or AF bikes.
4x 11.5mm O-rings
4x reducers
4x bushings
2x bolts and tear drop nuts
NZ delivery only.
Seattube rubber protector (50A durometer - soft and supple like your Minions.. ) to stick onto the swing arm of your Carbon Ripmo or Ripley V4 frame to guard against rock deflection onto the lower link.
Use this link for the instruction manual for installation
Fitment is for carbon Ripmo and Ripley V4 frames only. DOES NOT fit any of the Mojo HD's or Mojo 3, earlier Ripleys or the Ripmo/Ripley AF.
This is the protection piece for carbon frames that have the upper link attachment point behind the seat tube. If you need to replace it or add one, it's as easy as peeling off the backing, cleaning the area on your frame, and applying it to the best fit you can. It may be easier to remove the upper link to allow for more working room.
NZ delivery only.
Replacement axle for models with the UDH.
Length 174mm
Thread Pitch 12x1.0
Torque to 10nm
43 grams
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
Ibis Logo T-Shirt
Size: XL
Colour: Orange with Black Ibis logo
Cotton Polyester
NZ delivery only.
Finally putting the Ride More Work Less logo to good use, this handy flask will safely house the fine contents of any tasty beverage. Made of 18/8 grade stainless and holds 4oz of goodness. UV cured printed logo.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
COMPATIBLE WITH
Ripmo AF
Ripmo 1 - 2
Ripmo V2 S
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts.
NZ delivery only.
4 mounting bolt kit for upper links.
Compatible With
Ripmo AF
Ripmo 1 - 2
Ripmo V2S
HD5
HD4
HD3
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
This is the service kit needed when performing maintenance of the swingarm bushings on an Ibis aluminum frame. After an extended period of use, you might want to check these bushings for wear.
2x Igus Bushings
4x Reducer hardware (2x outer; 2x inner)
4x O-rings: 2 each of 1mm x 16mm & 1mm x 21 mm
2x Clevis to swingarm bolts
*Please note this kit is not compatible with the RipMo carbon frames*
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
COMPATIBLE WITH
Ripmo AF
Ripmo 1 - 2
Ripmo V2 S
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts.
NZ delivery only.
This is the kit to replace your lower links for any of current Ibis model that use this style link.
Ripmo 1, 2, V2S & AF
Ripley 4, V4 S & AF
HD5
All the hardware and replacement bushings / o-rings are included.
NZ delivery only.
4 mounting bolt kit for upper links.
Compatible With
Ripmo AF
Ripmo 1 - 2
Ripmo V2S
HD5
HD4
HD3
This is the protection piece for carbon frames that have the upper link attachment point behind the seat tube. If you need to replace it or add one, it's as easy as peeling off the backing, cleaning the area on your frame, and applying it to the best fit you can. It may be easier to remove the upper link to allow for more working room.
NZ delivery only.
Seattube rubber protector (50A durometer - soft and supple like your Minions.. ) to stick onto the swing arm of your Carbon Ripmo or Ripley V4 frame to guard against rock deflection onto the lower link.
Use this link for the instruction manual for installation
Fitment is for carbon Ripmo and Ripley V4 frames only. DOES NOT fit any of the Mojo HD's or Mojo 3, earlier Ripleys or the Ripmo/Ripley AF.
Compatible With
Ripmo V1
Ripmo V2
Ripley V4
Polycarbonate
Protects Downtube from Rock Strikes
Lightweight
Mounts via 2 Under Downtube Bolts on the carbon Ripmo and Ripley V4 frames. Bolts do not come with guard as they should be affixed to your bike frame. If you need a spare bolt let us know.
NOTE: This does NOT work on the Ripmo AF.
Available in black and, well, black
NZ delivery only.
This is the bushing kit for the clevis to swingarm bushings on the carbon V1 & V2 Ripmo. After an extended period of use, you might want to check these bushings for wear.
Full Kit with Bolts includes:
2 x clevis bolt and tear drop nut set
2x Igus Bushings
4x Reducer hardware (2x outer; 2x inner)
4x O-rings (1.2 x 17 mm)
Kit without Bolts includes:
2x Igus Bushings
4x Reducer hardware (2x outer; 2x inner)
4x O-rings (1.2 x 17 mm)
*Please note this kit is not compatible with the RipMo AF*
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Compatible With
Mojo HD4 - 5
Ripley 4
Ripley V4S
Ripmo 1 - 2
Ripmo V2S
Ripmo AF
This is the kit to replace the forward and rear shock mounting bolts. Contains
1 x Forward Aluminum bolt
1 x Rear Titanium bol
NZ delivery only.
Here's the necessary parts to refresh your lower link system.
4x link shaft bushings
4x 20mm o-rings
COMPATIBLE WITH
Ripmo 1 - 2
Ripmo AF
Ripley 4
Ripley AF
Mojo HD5
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
6061-T6 aluminum axle with hard ano finish. Available for SRAM or Shimano (142 and BOOST); pick which one you need from the drop down.
Weighs 40g
Use the SRAM version for the following 142 x 12mm Ibis models:
Mojo HD3 with 142mm rear
First Generation Ripley (Blue or Black/Green)
Mojo HDR
Mojo HDR 650b
Tranny 29
Mojo SL-R
Mojo HD with 142 x 12 rear axle
Use the Shimano 142 version for:
V2 Ripley (Orange or Black)
V2 Ripley LS
Hakka MX
Use the 148 Boost (Shimano standard) version for:
Ripley 4, V3, V2 with 148 Boost Swingarm
DV9
Mojo 3
Mojo 4
Mojo HD3 with 148 Boost Swingarm
Mojo HD4
Mojo HD5
RipMo
RipMo AF
Ripley AF
NOTE: There is not a numerical torque figure for the Hexle. We recommend tightening the 5mm with your multi tool that you carry with you. This way you’ll be able to remove it in case of a flat out on a ride.
ANOTHER NOTE: If you are looking to retrofit your non-Ibis bike with one of our Hexle's, you'll need to know the standard or thread pitch. For some reason, our industry has decided we need three different thread pitches for through axles:
Syntace, Specialized and DT use 12x1.0
Shimano is 12x1.5
Rock shox maxle is 12x1.75
Your bike manufacturer should be able to tell you which of these you need.
For reference here are the shaft lengths of all three options:
SRAM 142: 175mm
Shimano 142: 165mm
Shimano 148 Boost: 171mm
NZ delivery only.
Compatible With
Mojo HD5
Mojo 4
Downtube Rock guard
Polycarbonate
Protects downtube from rock strikes
Includes stainless steel M4x10 mounting bolts
Available in 2 sizes per your specific frame size
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
Ibis Mojo 3 Upper Link Assembly
Forged Aluminum
CNC machined
Anodized finish
Includes bearings & 4 mounting bolts
Super easy to replace
No special tools needed
NZ delivery only.
Mojo 3/ Ripley V2 Clevis Bushing Service Kit
Parts kit for Ripley & Mojo3 Clevis to Swing Arm w/ bolts
NZ delivery only.
This is for the Lower / Rear eyelet that connects to the clevis.
15mm wide with an 8mm bore
Fits following models:
Alloy Frames
Exie
HD6, HD5, HD4
Mojo 3, Mojo 4
Ripley 4
Ripley V4S
Ripley V5
Ripmo 1-2
Ripmo V2S
Ripmo V3
Included in the 4 piece kit is an eyelet bushing, black-ano rod, and two plastic spacers.
NZ delivery only.
Replacement eyelet hardware from Fox.
This kit will allow you to refresh an existing shock or an aftermarket shock that doesn't come with the correct hardware to match the specs of our current models.
Fox part numbers for reference: Front 21.8mm wide: 803-03-165
Fits following models:
Mojo 3
HD4
HD5
Ripley 1 & 2
NZ delivery only.
This is the set to install a lower link to a Mojo 3 or HD3 with boost 148 swingarm.
2 link shafts and 2 fixing bolts.
Torque to 24nm, Loctite 243 recommended.
NZ delivery only.
Compatible With
Mojo 3
Mojo HD3
Mojo HD4
Polycarbonate
Protects Cables and Downtube from Rock Strikes
Lightweight
Mounts via 2 Under Downtube Bolts on Mojo HD3 or Mojo3 SM/MD frame, 4 bolts on LG/XL size frame. Bolts do not come with guard as they should be affixed to your bike frame.
Available in 2 sizes
NZ delivery only.
If you want to mount a chain guide on your Ibis, you will need one of these.
When using SRAM DUB cranks along with the ISCG plate on a RipMo or any frame with a 73mm bottom bracket shell width, you will need the SRAM DUB 2mm spacer inside the drive side crank arm against the bottom bracket shell.
It's aluminum. ISCG 05 standard
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
Ibis Mojo, Mojo SL, and Tranny 26.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
Ibis Mojo, Mojo SL, and Tranny 26.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
142 / 148 Models: The HD, HD-R, SL-R, HD3/4/5, DV9, Ripley and Ripley LS, Mojo 3 and Ripmo & Ripmo AF all use the same hanger.
NOTES:
The earlier Mojo HD with 135mm rear wheel spacing uses a different mount.
The Mojo SL hanger works on the Ibis Mojo, Mojo SL, and Tranny 26.
The hanger designed for the New Mojo 3 and Ripley/ Ripley LS will fit all previous 142 models. It does not require the backing nut of the two-piece fixing bolt assembly as the new hanger has threads built in for the standard chainring bolt used.
NZ delivery only.
T29 Slot Machine lower assembly includes a new stainless steel bolt and nut to increase the overall strength and longevity of the slot machine function. The alloy conical washer and stainless washer are still used.
Upper yoke assembly includes machined titanium shaft and a teardrop shaped nut.
Let us know if you need a new outer gasket for the lower box section of the frame info@hyperformance.nz
Finally putting the Ride More Work Less logo to good use, this handy flask will safely house the fine contents of any tasty beverage. Made of 18/8 grade stainless and holds 4oz of goodness. UV cured printed logo.
NZ delivery only.
Replaceable Aluminum Derailleur Hanger.
Ibis Mojo, Mojo SL, and Tranny 26.
NZ delivery only.
Factory spec Slot Machine assembly includes the aluminum shaft, conical washer, and grade 12.9 steel 5mm bolt.
When you want to run your 26" Tranny as a single speed, you don't need a derailleur hanger
But you probably DO need a bottle opener (since you're a rad root beer drinkin' single speeder)
The Tranny Single Speed Hanger incorporates a bottle opener into the hanger.
NZ delivery only.
SRAM XD (not compatible w/ XDR cassette)
Designed for Ibis Logo Wheels, it comes with six pawls set in two phases. This neat little trick doubles the engagement, giving you a snappy 72 Points of Engagement (POE).
Compatibility:
These freehub bodies are for the Ibis branded hubs found on Ibis line of wheels (2017 and newer) including the Send 1/2, S35/S28 Logo, 733, 735 Logo, 738/938, 933, and the 742/942 Logo wheelsets.
SRAM XDR cassettes are not compatible with the XD freehub body.
Ibis do not offer a high engagement 6 pawl freehub body for Shimano 11 Speed Road Freehub body or HG/Standard. If you are installing a road cassette on a Hakkalugi MX or any bike with Ibis wheels, you must order our 4 pawl freehub body.
11-speed cassettes for road bike drivetrains use a different spacing from mountain 10 & 11-speed cassettes. Ibis have 4-pawl freehubs available for our Ibis branded hubs for this type of application.
Installation Notes:
The XD freehub body utilizes a drive side endcap (included).
Wheel Size | 29"
Material | Aluminium
Drillings | 32 hole
Rim Width Inner | 35mm
Asymmetric Rim | means that instead of the spoke holes being drilled through the center of the rim, they're slightly offset. Doing this allows Ibis to improve the bracing angle of the spokes. The larger offset allows IBIS to tension both sides of the wheels nearly equally, which results in a stronger and more durable wheelset.
